USB audio converters
-
- Senior Member
- Posts: 851
- Joined: Sun Sep 12, 2010 3:14 pm
- Location: South Jordan, Utah
Re: USB audio converters
Last week we used the following device:
https://www.amazon.com/Microphone-HOSON ... B07ZBZ62X9
I didn't notice any distortion during testing but there was distortion during the webcasts, with two different computers, so I assume it could only handle mic level. But now I see that the specs say it can handle 2.8V. So I'm not sure what's up; the specs are for both an XLR to USB and a TRS to USB. It does say something about 20db of gain though. Maybe we just need to turn the mic level down? I didn't know you could do that, thanks.
https://www.amazon.com/Microphone-HOSON ... B07ZBZ62X9
I didn't notice any distortion during testing but there was distortion during the webcasts, with two different computers, so I assume it could only handle mic level. But now I see that the specs say it can handle 2.8V. So I'm not sure what's up; the specs are for both an XLR to USB and a TRS to USB. It does say something about 20db of gain though. Maybe we just need to turn the mic level down? I didn't know you could do that, thanks.
Craig
South Jordan, UT
South Jordan, UT
-
- Community Administrator
- Posts: 34503
- Joined: Sat Jan 20, 2007 2:53 pm
- Location: U.S.
Re: USB audio converters
A mono "computer" microphone is TRS. Tip and Sleeve has the signal, the ring is power for electret mics. I'm not sure of the details, but apparently, shorting the power to ground by using a TS cable messes up the sound card. Using a TRS cable and leaving the R open on the other end might pick up noise, but otherwise doesn't cause issues.craiggsmith wrote:One thing I wonder about is using a mono vs stereo audio cable. I found two other similar devices on Amazon (https://www.amazon.com/gp/product/B07SSBHGP7 and https://www.amazon.com/gp/product/B01N905VOY) and both say the the microphone jack is not compatible with TS cables, only TRS. Yet it's mono. I can't imagine it expects a balanced input, and even if it did it wouldn't matter if the other channel had no signal. And with an unbalanced mono source it wouldn't matter which cable is used, the ring would just be grounded right. Right?
Have you searched the Help Center? Try doing a Google search and adding "site:churchofjesuschrist.org/help" to the search criteria.
So we can better help you, please edit your Profile to include your general location.
So we can better help you, please edit your Profile to include your general location.
-
- Member
- Posts: 158
- Joined: Fri Jan 28, 2011 3:59 pm
- Location: Herriman, UT
Re: USB audio converters
Sometime I can get specs by contacting the manufacturer, but more often I have to obtain the product and use my signal source, DVM, o'scope and the TrueRTA program to make measurements. The TrueRTA program works great for viewing a waveform (finding the point of distortion), but it's amplitude is not calibrated so I use a DVM or oscope paralleled with the input signal.craiggsmith wrote:Thank you both for the recommendations. Where did you get the specs for the Sabrent device? I can't find max input level for any of the devices anywhere.
A TS cable should be avoided because it shorts the bias or the mic+bias signals to ground.craiggsmith wrote: One thing I wonder about is using a mono vs stereo audio cable. I found two other similar devices on Amazon (https://www.amazon.com/gp/product/B07SSBHGP7 and https://www.amazon.com/gp/product/B01N905VOY) and both say the the microphone jack is not compatible with TS cables, only TRS. Yet it's mono. I can't imagine it expects a balanced input, and even if it did it wouldn't matter if the other channel had no signal. And with an unbalanced mono source it wouldn't matter which cable is used, the ring would just be grounded right. Right?
All of the TRS Mic connections I have seen on computers and USB adapters are unbalanced and either
T=mic, R=bias, S=Return
TR=mic+bias, S=Return
T=L Mic+Bias, R = R Mic+Bias , S=Return
If you are running a 50-75 foot TRS cable from the RecordOut jack it would be advisable to put a TS to TRS adapter (mono to stereo) at the RecordOut jack to prevent the "R" from becoming a 50ft antenna for noise. You may not need it but the adapter is only $2 and it's handy to have in your "bag of problem solving adapters"!
-
- Senior Member
- Posts: 851
- Joined: Sun Sep 12, 2010 3:14 pm
- Location: South Jordan, Utah
Re: USB audio converters
russellhltn wrote:A mono "computer" microphone is TRS. Tip and Sleeve has the signal, the ring is power for electret mics. I'm not sure of the details, but apparently, shorting the power to ground by using a TS cable messes up the sound card. Using a TRS cable and leaving the R open on the other end might pick up noise, but otherwise doesn't cause issues.
Thanks very much. I didn't know computers were capable of providing power for mics. Since most computers nowadays don't have separate headphone and mic jacks but rather a single TRRS jack, I assume the bias is applied directly to the signal? I certainly wouldn't want to short that to ground at any rate.CalS201 wrote:A TS cable should be avoided because it shorts the bias or the mic+bias signals to ground.
All of the TRS Mic connections I have seen on computers and USB adapters are unbalanced and either
T=mic, R=bias, S=Return
TR=mic+bias, S=Return
T=L Mic+Bias, R = R Mic+Bias , S=Return
If you are running a 50-75 foot TRS cable from the RecordOut jack it would be advisable to put a TS to TRS adapter (mono to stereo) at the RecordOut jack to prevent the "R" from becoming a 50ft antenna for noise. You may not need it but the adapter is only $2 and it's handy to have in your "bag of problem solving adapters"!
But this begs the question of what the input looks like for the Sabrent devices. I called them earlier today (they actually have a tech support line and picked up right away) to find out the max input voltage of that other device, but it took them a long time to come up with an answer and they said 3.5V, which seems highly unlikely. So I don't know if they will know the pin configuration or not.
Craig
South Jordan, UT
South Jordan, UT
-
- Member
- Posts: 158
- Joined: Fri Jan 28, 2011 3:59 pm
- Location: Herriman, UT
Re: USB audio converters
Yes, Mic signal and bias voltage both appear on the "S" of a computer or modern phone TRRS jack.craiggsmith wrote:Thanks very much. I didn't know computers were capable of providing power for mics. Since most computers nowadays don't have separate headphone and mic jacks but rather a single TRRS jack, I assume the bias is applied directly to the signal?
The Mic input for the SAbrent USB adapter is a TRS with the following pin configuration:craiggsmith wrote:But this begs the question of what the input looks like for the Sabrent devices. I called them earlier today (they actually have a tech support line and picked up right away) to find out the max input voltage of that other device, but it took them a long time to come up with an answer and they said 3.5V, which seems highly unlikely. So I don't know if they will know the pin configuration or not.
T=Mic+bias voltage
R=open
S=Return
The bias voltage is 3v open circuit, 1.5v when you attach a 10K source, and .5v when you attach a 2K source.
The maximum input is 550mv rms/777mv pk as I described in a previous post viewtopic.php?f=27&t=37755#p215749
-
- Community Administrator
- Posts: 34503
- Joined: Sat Jan 20, 2007 2:53 pm
- Location: U.S.
Re: USB audio converters
If R is open, then it seems like it should be happy with a TS cable.CalS201 wrote:The Mic input for the SAbrent USB adapter is a TRS with the following pin configuration:
T=Mic+bias voltage
R=open
S=Return
Have you searched the Help Center? Try doing a Google search and adding "site:churchofjesuschrist.org/help" to the search criteria.
So we can better help you, please edit your Profile to include your general location.
So we can better help you, please edit your Profile to include your general location.
-
- Senior Member
- Posts: 851
- Joined: Sun Sep 12, 2010 3:14 pm
- Location: South Jordan, Utah
Re: USB audio converters
Thank you. Yes, I saw your previous post, I was wondering about the other Sabrent device I listed. I don't like the one initially mentioned as it blocks the adjacent ports unless I buy a separate cable; the one I listed comes with a cable for the same price. But I'm not sure if it's the same internals or not. Most of the description is similar but it also says it "enables PC style 3.5mm headsets with microphone to be used on your Mac." Not sure how you could do that with separate mic and headphone jacks.CalS201 wrote:The Mic input for the Sabrent USB adapter is a TRS with the following pin configuration:
T=Mic+bias voltage
R=open
S=Return
The bias voltage is 3v open circuit, 1.5v when you attach a 10K source, and .5v when you attach a 2K source.
The maximum input is 550mv rms/777mv pk as I described in a previous post viewtopic.php?f=27&t=37755#p215749
Last edited by craiggsmith on Tue Oct 27, 2020 3:39 pm, edited 1 time in total.
Craig
South Jordan, UT
South Jordan, UT
-
- Senior Member
- Posts: 851
- Joined: Sun Sep 12, 2010 3:14 pm
- Location: South Jordan, Utah
Re: USB audio converters
Awesome.CalS201 wrote:Sometime I can get specs by contacting the manufacturer, but more often I have to obtain the product and use my signal source, DVM, o'scope and the TrueRTA program to make measurements. The TrueRTA program works great for viewing a waveform (finding the point of distortion), but it's amplitude is not calibrated so I use a DVM or oscope paralleled with the input signal.
I see them from audio retailers but having a hard time finding one on Amazon. I'm only running a 6 foot cable but I'll try to get one eventually.CalS201 wrote:If you are running a 50-75 foot TRS cable from the RecordOut jack it would be advisable to put a TS to TRS adapter (mono to stereo) at the RecordOut jack to prevent the "R" from becoming a 50ft antenna for noise. You may not need it but the adapter is only $2 and it's handy to have in your "bag of problem solving adapters"!
Craig
South Jordan, UT
South Jordan, UT
-
- Community Administrator
- Posts: 34503
- Joined: Sat Jan 20, 2007 2:53 pm
- Location: U.S.
Re: USB audio converters
Here you go:craiggsmith wrote:I see them from audio retailers but having a hard time finding one on Amazon. I'm only running a 6 foot cable but I'll try to get one eventually.
3.5mm Mono Plug to 3.5mm Stereo Jack
3.5mm Stereo Plug to 3.5mm Mono Jack Adaptor
Have you searched the Help Center? Try doing a Google search and adding "site:churchofjesuschrist.org/help" to the search criteria.
So we can better help you, please edit your Profile to include your general location.
So we can better help you, please edit your Profile to include your general location.
-
- Senior Member
- Posts: 851
- Joined: Sun Sep 12, 2010 3:14 pm
- Location: South Jordan, Utah
Re: USB audio converters
Thanks!russellhltn wrote:Here you go:
3.5mm Mono Plug to 3.5mm Stereo Jack
3.5mm Stereo Plug to 3.5mm Mono Jack Adaptor
Craig
South Jordan, UT
South Jordan, UT